Home > Cannot Open > Cannot Open Etc Mnttab For Read

Cannot Open Etc Mnttab For Read

If that doesn't work, reboot the machine at your convenience. Some SCSI devices for thePC market do not meet the high I/O speed requirements for the UNIX market.Ā  Other possible causes of this problem are improper cabling or termination, and power If the targeting of the internal disk drive is in question, power off the machine, remove all external drives, turn the power on, and from the PROM monitor run the probe-scsi-all In Konqueror, when I double-click on a cd drive to see what's inside, I get Could not mount device. have a peek here

Try remounting the filesystem on top of itself or shutting down any client processes that refer to stale file handles. The file system containing /etc might be mounted read-only, or not mounted at all. When a systemis running the automounter, do not mount local filesystems on the /home directory. I also tried searching both hard drives for bad blocks with "badblocks -sv /dev/hda" that I found in another post, but when it finally finished, it reported no bad blocks for http://docs.oracle.com/cd/E19620-01/805-4036/msgs-2036/index.html

The high-level steps to recover from improper /etc/vfstab file entries are as follows: Booting the system to single-user mode Running the fsck command on the mirror volume Remounting file system read-write It is also possible that a user is not allowed to create anymore processes. The mount command assumes that a local mount is being done unless the -f flag is used on the command line or the requested directory as listed in /etc/default/filesys specifies filesystem If SCSI device targeting is acceptable, memory configuration could be the problem, especially for machines with the sun4c architecture.

See exportfs(NADM) and exports(NF) for more information. Find More Posts by gnashley Thread Tools Show Printable Version Email this Page Search this Thread Advanced Search Posting Rules You may not post new threads You may not post sendmail[N]: NOQUEUE: SYSERR: net hang reading from variable 190. Operation not applicable This error indicates that no system support exists for some function that the application requested.

If you are writing a program that produces this message while calling a system library, try to find and use an alternative library function. After a user has removed or modified a host in the hosts database, statd might not properly purge files in these directories, which results in its trying to communicate with a Minimize the amount of time you run with submirrors disabled or offline. https://www.veritas.com/support/en_US/article.000005141 For security reasons, it is a bad idea to allow root logins from anywhere besides the console.

If I remember anything I'll update againšŸ™‚ Search for: Blogroll Ben Rock blog c0t0d0s0 Oracle Observatory Blog Oracle Solaris Recommended Reading Planet OpenSolaris Solaris Performance Blogs Archives August 2012(1) rx framing error Usually this error indicates a hardware problem. The symbolic name for this error is EACCES, errno=13. If the software has encountered a failure, other slices on the same disk will likely experience failures soon.

SCSI bus DATA IN phase parity error The most common cause of this problem is unapproved hardware. click to read more Perhaps it could not read that line in the file, or it could not find the filesystem, or else the filesystem name was not a locally mounted filesystem. Anyway, I really enjoy running Slackware (I'm running Slackware current). Sorry, we couldn't post your feedback right now, please try again later.

What about my fstab do you think is wrong? http://dekovsoft.com/cannot-open/unable-to-open-connection-to-com3-unable-to-open-serial-port.html variable is set to true. The most likely reason is that the metaroot command was not used to maintain the /etc/system and /etc/vfstab files, or an old copy of the/etc/vfstab file was copied back. The issue was due to the Mount VCS Agent unable to create a new file descriptor, as it had already reached the 256 Solaris default soft limit, andĀ more than 1000 such

Well, I did just as you said and I found out that the permissions of /etc/fstab is read-write only for root. Share Errors, messages, solaris error messages, unix error messages Leave a Reply Cancel reply Your email address will not be published. My Name is Gopi.Ā  I like to share the knowledge with people what I know. Check This Out It it does, ask the vendor or author of the application for an update.

Operation not applicable 167. The following examples show the output of the file and adb commands on a core file from the dtmail program. $ file core core: ELF 32-bit MSB core file SPARC Version Boot of CDROM.

No transactions found Zero bit found in on-disk bitmap after the last valid bit.

I have another slack-box that I just got running and /etc/mtab exists on it and fstab is also set to read-write only for root on that computer. Check the Ethernet cabling and connectors to locate a problem. This message indicates that no system support exists for an operation. If there is at least one valid recipient, each invalid recipient address will generate a "User unknown" message.

Look at the source code that made this socket request and check that it requested one of the types specifiedin /usr/include/sys/socket.h. Segmentation Fault Segmentation faults usually result from programming error. Reboot single user (for example with boot -s) and run ls -l /dev/bd* to see if this is the problem. http://dekovsoft.com/cannot-open/cannot-open-an-anonymous-level-security-token-window-open.html Read-only file system 177.

It is followed bythe advisory "Please, replace tape cartridge" message. Does this other box have the same problem? Any data written during this condition will probably be lost. will get below error.

I tried copying it to /etc using Konsole and I get # cp mtab /etc cp: cannot stat `/etc/mtab': Permission denied I even tried to create a blank text file /etc/mtab By using this site, you accept the Terms of Use and Rules of Participation. End of content United StatesHewlett Packard Enterprise International CorporateCorporateAccessibilityCareersContact UsCorporate ResponsibilityEventsHewlett Packard LabsInvestor RelationsLeadershipNewsroomSitemapPartnersPartnersFind a PartnerPartner Last edited by theo444; 08-22-2005 at 03:29 PM. When executed, it assumes the root priviledges to read /etc/mnttab file and provide the output.

ROOT LOGIN /dev/console This syslog message indicates that someone has logged in as root on the system console. When a system is running NIS+, the login program firstperforms UNIX authentication, and then attempts a keylogin(1) for secure RPC authentication. I don't think that it is the hard drives, since they're both reliable Seagate drives that I've been using for a while (though I can't get reiserfsck to check the reiserfs I'd hate to have to reinstall all over again after getting settled down and making a whole bunch of tweaks.

The tasks in this section provide solutions to such potential problems.