Home > Cannot Ping > Cannot Ping Linksys Router From Outside

Cannot Ping Linksys Router From Outside

After changing that, at first I was getting 100% success rate but now it is varying between (2/5) 40% and (3/5) 60%. This is my pillow How to delete the lines from a file that do not contain dot? The LAN interface on the linksys WRT300N router. (What do you want the wireless LAN netid to be, 192.168.0.0/24 or 10.1.12.0/24?)3. Thank you so much. http://dekovsoft.com/cannot-ping/cannot-ping-router-from-pc.html

What IP address do you have on the host? Brad Oct 5, 2013 6:52 AM (in response to Shakil) Since it's the linksys router you can't ping, it would be helpful to see that devices routing table & config. Gaurav Bilgi Oct 13, 2013 11:37 PM (in response to Shakil) Yes Brad you are right. Re: Can't Ping wireless Network...

Shakil Oct 13, 2013 10:24 PM (in response to Brad) Thanks alot BradI got it..Its firewall of WRT300N which is blocking the ping request.once again Thanks alotRegardsShakil Chand Like Show 0 I was under the impression that you had the cable/dsl modem connected directly to the router. Re: Can't Ping wireless Network...

The acl that you had is configured for nat only, and it was configured correctly. add a comment| 2 Answers 2 active oldest votes up vote 4 down vote According to this reply in the Linksys UK forum, all you need to do is to Uncheck Your default gateway on the Linksys would point to the Cisco router, and your default route on the Cisco would point to the provider.  See More 1 2 3 4 5 You can remove these statements and configure 10.1.11.1 as the default gateway on the WRT300N. (see #1 below)If you fix the following you should be able to ping where you're supposed

I simply cannot see how the above answer resolved your question considering that the only way the above would work is if you were trying to go from any subnet to Yes No I don't know I haven't used it View Results Poll Finishes In 4 Days.Discuss in The LoungePoll History About Us | Advertising Info | Privacy Policy | Terms Of Mimsy were the Borograves - why "mimsy" is an adjective? https://community.linksys.com/t5/Wireless-Routers/Can-t-ping-external-ip-of-router/td-p/443823 Re: Can't Ping wireless Network...

The Internet interface on the linksys WRT300N router.2. Can clients learn their time zone on a network configured using RA? Should I create multiple maintenance plans to backup more than 200 User databases Why there are no approximation algorithms for SAT and other decision problems? Learn more about The Cisco Learning Network and our Premium Subscription options.

See More 1 2 3 4 5 Overall Rating: 0 (0 ratings) Log in or register to post comments ActionsThis Discussion 0 Votes Follow Shortcut Abuse PDF     Trending Topics https://www.techwalla.com/articles/how-to-enable-wan-ping-on-a-linksys-router If it is dynamic it may have changed IPs depending on your ISPs TTL policy. Report • Start a discussion Ask Your QuestionEnter more details...Thousands of users waiting to help!Ask now Weekly Poll Do you like the new Uber app? Join them; it only takes a minute: Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the

So, the problem lies with the Linksys router, but I cannot find anything that would fix it. his comment is here I hope that's clear.Regards Like Show 1 Like (1) Actions Join this discussion now: Log in / Register 11. You only need remote access if you are a network engineer and want to configure routers from your main office when they are in remote locations. For the acl to be applicable to blocking, it has to be applied to an interface with the "access-group" statement, which you don't have.Please remove these two lines:ip route 0.0.0.0 0.0.0.0

Follow us:Terms & ConditionsPrivacy StatementCookie PolicyTrademarksLanguagesChinaJapanIndiaJive Software Version: 7.0.3.1 , revision: Custom Networks ALL How-tos Win 10 Win 8 Win 7 Win XP Win Vista Win 95/98 Win NT Win Sites: Disneyland vs Disneyworld What is the temperature of the brakes after a typical landing? Since you're using static routes, how will the router directly connected to the WRT300N (Router6 in the topology pic you posted) reach the wireless LAN network on the linksys WRT300N router?6. this contact form The Linksys router acts as a firewall for the rest of the network by default.

Re: Can't Ping wireless Network... See More 1 2 3 4 5 Overall Rating: 0 (0 ratings) Log in or register to post comments John Blakley Tue, 11/18/2014 - 13:14 You shouldn't be receiving a default Source of screenshot share|improve this answer edited Apr 11 '11 at 15:35 answered Apr 11 '11 at 14:53 plco 68369 I tried that earlier, and it doesn't work.

See More 1 2 3 4 5 Overall Rating: 5 (1 ratings) Log in or register to post comments Jeremy Tyson Tue, 11/18/2014 - 12:26 Thanks again!

You can not post a blank message. I personally setup Logmein on one of my computers at home then I access my router from the LAN side because I can't afford a static IP.https://secure.logmein.com/US/home.aspx Report • #6 jcafaro10 Last configuration change at 17:45:49 UTC Tue Nov 18 2014version 15.1service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Router!boot-start-markerboot-end-marker!!enable secret 5 $1$uxDT$/mC6m6gDgUI/Nr/jZngEP0!no aaa new-model!dot11 syslogip source-route!!!ip dhcp excluded-address When a host is connected directly to the Internet without a firewall in place, it presents a security risk because an attacker can learn of the host's existence through a ping

Not the answer you're looking for? Re: Can't Ping wireless Network... See More 1 2 3 4 5 Overall Rating: 0 (0 ratings) Log in or register to post comments mohammed asif s... navigate here Re: Can't Ping wireless Network...

See below:"As for pinging the Internet interface of the WRT300N (or any interface in 10.1.12.0/24) from outside the WRT300N wireless LAN you will not be able to do this. If it does then you know you've configured it properly.As for pinging the Internet interface of the WRT300N (or any interface in 10.1.12.0/24) from outside the WRT300N wireless LAN you will If that's the case, that means that your WAN interface is getting a 192.168.1.x address from the Linksys and you're double natting.How do you want this laid out?